QC Copper and Gold Inc. (TSXV: QCCU) (OTCQB: QCCUF) ('QC Copper' or the 'Company') is pleased to report the results from an additional 13 diamond drill holes with multiple wide stacked intersections of copper mineralization.

These results continue to emphasize the gold-rich nature of the veins in the southern part of the Springer conceptual pit and highlight high copper grades on Perry and the open pit resource potential of the Eastern Veins.

These results continue to provide encouragement that the revised mineral resources estimate (MRE) that is currently being prepared will improve over the 2021 MRE which generated a resource of 81.7 million tonnes at a grade of 0.65% Copper and 0.31 gpt Gold in the Measured and Indicated categories and an additional 21.4 million tonnes at 0.51% Copper and 0.30 gpt Gold.

Southern Springer Pit Area (near Gwillim Fault)

Assay results for the southern limit of the Springer pit continue to surprise with higher gold grades near the Gwillim Fault. The holes were collared to intersect Veins 4 and 5 and hole 248 intersected 2.95 gpt old over 2.8m followed by a second interval spanning 4.8m which assayed 1.1 gpt Gold and 1.5% Copper. Hole 253 returned two significant mineralized intervals with the first grading 0.79% Copper and 0.50 gpt Gold over 9.0m starting at 40.5m, followed immediately by 0.36% Copper and 0.25 gpt Gold over 100.5m starting at 64.5m. In addition, hole 250 and 255 returned 73.5m with 0.37% Copper and 0.22 gpt Gold and 55.5m with 0.44% Copper and 0.30 gpt Gold, respectively.

Perry Mine Area

Results for the Perry Mine area confirmed that the mine operators overlooked some high grade copper veins. Hole 245 intersected 1.68% Copper over 4.5m from 154.5m, immediately followed by 0.95% Copper and 0.22 gpt Gold over 9.0m from 174m.

Eastern Veins

The Eastern Veins were drilled for a potential satellite pit and results are confirming expectations. Hole 247 returned three mineralized intervals with the first one returning 0.39% Copper over 6.0m followed by 0.34% Copper over 4.0m followed by 0.26% Copper over 22.5m. Hole 252 intersected a very high copper grade of 6.36% Copper and 0.14 gpt Gold over 2.9m followed by 0.33% Copper over 10.5m.

QP Statement

The technical information contained in this news release has been reviewed and approved by Charles Beaudry, P.Geo and geo., Director and Vice President Exploration for QC Copper & Gold, a Qualified Person, as defined in 'National Instrument 43-101, Standards of Disclosure for Mineral Projects.' For the exploration undertaken by QC Copper & Gold, all assay batches are accompanied by rigorous Quality Assurance procedures, including the insertion of standards and blanks and verification assays in a secondary laboratory. All the core received from the drill is split in half, bagged and sent to ALS-Global facilities in Quevillon, Quebec for sample preparation and then the pulps are shipped to AlS-Global's Vancouver laboratory or some other location in the world for analysis using ALS-Global's standardized ISO-compliant methods, all of which are listed in the laboratory certificates provided with the assay results. The remaining half core along with the rejects and the pulps returned from the laboratory are securely stored at QC Copper's facilities in Chapais, Quebec. Quality Control results, including the laboratory's control samples, are evaluated immediately on reception of batch results and corrections are implemented immediately if necessary. All drill collars are surveyed and positioned in UTM coordinates. Collars are oriented using a gyroscopic north-finding system and downhole deviations surveys are done with a single-shot gyroscopic instrument at 30 to 50m intervals. For veins oriented approximately east-west and dipping towards the north, and drill holes oriented due south and plunging between 50 and 65 dips, the true width of mineralized intersections are equal or greater than 80% of the quoted core length composite intervals. This observation also holds for veins oriented northwest-southeast and dipping towards the northeast with holes drilled towards the southwest at 225 degrees with dips between 50 and 65 degrees. However, for other drill hole orientations relative to these veins or other less common vein orientations, the true widths of mineralized intersections are less.

Contact:

Tel: 416.644.1571

Email: sstewart@qccopper.com

Certain information in this press release may contain forward-looking statements. This information is based on current expectations that are subject to significant risks and uncertainties that are difficult to predict. Actual results might differ materially from results suggested in any forward-looking statements. QC Copper and Gold Inc. assumes no obligation to update the forward-looking statements, or to update the reasons why actual results could differ from those reflected in the forward looking-statements unless and until required by securities laws applicable to QC Copper and Gold Inc. Additional information identifying risks and uncertainties is contained in filings by QC Copper and Gold Inc. with Canadian securities regulators, which filings are available under QC Copper and Gold Inc. profile at www.sedar.com.

(C) 2023 Electronic News Publishing, source ENP Newswire